AUTONET TV

Clean Machine (Fuel and Air Induction Cleaning)

As your vehicle ages, its performance isn’t quite what it used to be, but many of us never notice the change because it’s gradual.  So here are a few questions to ask yourself.  Does your vehicle feel like it doesn’t have the pep that it used to? Have you noticed your fuel economy isn’t quite as good as it once was? Does it idle roughly or is it hard to start?  Do you hear the engine knocking? Has it recently failed an emissions test?

All of those can be signs that your fuel and air induction systems are dirty and need cleaning.  Your fuel system takes gasoline from the tank to the engine’s combustion chambers where fuel injectors spray fuel that mixes with air and is ignited by spark plugs.  Black carbon deposits eventually can build up, obstructing fuel flow and diminishing your engine’s performance and fuel efficiency.

The air induction system is what allows air to go into the engine’s combustion chamber.  Getting the proper air flow is necessary for you to quickly start your vehicle, accelerate, and perform the way it should and idle smoothly when you’re standing still.  Like the fuel system, your air induction system can get blocked up with deposits and other contaminants.

A professional fuel and air induction cleaning can help restore your performance and fuel economy, especially when you are experiencing problems.  A technician will use specialized chemicals that can remove the carbon buildup.  In extreme cases, they will remove the fuel injectors and clean them with specialized tools.  

After cleaning, you may notice how much more pep your vehicle has and how smoothly it runs.  Keep your fuel and air induction systems clean and enjoy your vehicle’s performance improvements.

Hill's Auto Repair, Inc.
22829 colton point rd
Bushwood, Maryland 20618
301-769-2400

Flat Tire? Three?s the Charm (Tire Repair)

For most drivers, at some point you’re going to have a flat tire. Depending on how it was damaged, it may have to be replaced.  But sometimes, a repair will do the trick, as long as the puncture isn’t on the sidewall and the hole is smaller than ¼ inch/6.35mm in diameter. Here are the three common ways your tire can be fixed.

One way is to put a plug in the hole.  Since most tires are damaged by running over sharp objects such as screws and nails, the small hole from which the air is escaping is on the part of the tire that touches the road. If it’s in the sidewall, it most likely can’t be fixed.  

In the plug method, a technician inserets a rubber plug.  It is covered with some sticky, gluey stuff, and is pushed into the hole from the outside. That plugs the hole and stays in place, thanks to the glue. Friction from driving heats it up and seals the deal.  

Another method is to patch the hole.  For this, your tire has to first be taken off the vehicle, then off the rim so the technician can get access to the inside. There, they’ll clean the inside surface around the hole and apply a rubber patch with an adhesive on it. This type of patch works well, and because of the extra steps and complexity, costs more than having your tire plugged.  

There’s also a combination of those methods just described, the plug-patch.  It is, in essence, a type of patch with glue on it that has a plug sticking out of it.  The plug is inserted into the tire from the inside and pulled through the hole from the outside, drawing the attached patch tight against the tire’s inside surface. The last two methods can’t be used if the hole is near another repair or the sidewall.    

The good news is if it’s fixed properly, your repaired tire should give you good service.

Hill's Auto Repair, Inc.
22829 colton point rd
Bushwood, Maryland 20618
301-769-2400

Timing is Everything (Timing Belt)

Talk about exquisite choreography; it happens under the hood of your vehicle every time you take a drive.  Your engine’s many complex parts must work exactly together.  One key is a part called a timing belt, which enables the synchronizing of two of your engine’s components, the camshaft, and the crankshaft.  

The timing belt coordinates the valves in your engine to open and close at the appropriate time to get exhaust out of the engine’s cylinders. Timing belts may also power the water pump and the oil pump.  The belt is made of rubber.  Some engines use a timing chain (made of metal). 

Your vehicle’s manufacturer recommends an interval after which you should have your timing belt or chain replaced, and that service should be part of your vehicle’s regular maintenance.  It’s always better to replace it before it breaks rather than after.  After all, if your timing belt breaks while you’re driving down the road, it throws off the whole sync of engine parts and can cause major damage to the type of engines most commonly used in vehicles today.

It's also important to remember that a timing belt is made of rubber, and rubber deteriorates with time, no matter how much use it gets. Have us look at your timing belt to see if it’s time to get it replaced.  

Here are some signs to look for that will let you know if your timing belt is failing. You might have trouble starting your vehicle, it may misfire or black smoke may come out the tailpipe. If you notice any of those symptoms, bring your vehicle in and have us take a look right away.  When it comes to your engine, timing is everything.

Hill's Auto Repair, Inc.
22829 colton point rd
Bushwood, Maryland 20618
301-769-2400

A Clean Connection (Battery Cleaning)

A clean connection is a wonderful thing.  Think of a good cell phone signal or an airline connection with ample time and short distance to the next gate. Good connections are also important for your vehicle’s battery, and one secret to that is to make sure it’s periodically cleaned.

If it’s been a while since you have had any service to your battery, bring it in so we can inspect it for any corrosion that might have formed.  Corrosion on the battery terminals will affect the connection between the battery and your vehicle’s electrical system. The amount of corrosion you can expect can be influenced by such things as the kind of climate you live in (dry or humid, warm or cold), if there’s lots of salt on the roads and how old your battery is.  

We have tools and chemicals to safely remove the corrosion for an optimal electrical connection. In order to reduce the amount of corrosion re-forming on the battery, we’ll apply a special protective coating.  

It’s also important to have your battery tested, especially if it’s more than a few years old or hasn’t been tested in a while.  Our equipment can measure how well a battery holds a charge and how much more life you should expect from it. We can discuss when you might expect to buy a new one, since a battery is definitely the kind of thing you don’t want to have fail you when you’re least expecting it.

Hill's Auto Repair, Inc.
22829 colton point rd
Bushwood, Maryland 20618
301-769-2400

Out of Joint (CV Joint and Boot Replacement)

If you have a front-wheel-drive vehicle, it has components called CV joints which enable you to turn your wheels smoothly. The CV stands for “constant velocity.” In essence, it’s a set of gears that connect a shaft that allows power from the transmission to be sent to the wheels.  When you turn the wheels, no matter what angle, the input velocity rotation will be equal to the output. Thus, the name, CV (constant velocity) joint. Other vehicles with 4-wheel drive and all-wheel drive also use CV joints.  

If one of your CV joints isn’t working right, you may find your vehicle difficult to handle.  If one breaks, your vehicle may stop moving.  So, it’s important that CV joints be in top working condition.  The joints need a lot of lubrication, so they are surrounded by grease.  There’s a rubber enclosure around them called the boot which holds the grease in and protects CV joints from the elements. 
 
The biggest problems come when one of those rubber boots cracks.  Water and dirt can then get into the joint, causing it to wear down and lose all its vital lubrication.  It’s important to have your CV joints inspected regularly so a technician can spot cracks before the CV joints are ruined.  Sometimes just the boot can be replaced before any major damage is done.  But when the joint does go bad, it must be replaced.  

Signs your CV joint needs changing out? You might hear a clicking sound when you turn if the CV joint is worn out. You might notice some thick, black grease around your wheel or on the pavement where you park your vehicle.  You might also feel your vehicle vibrate when you’re going fast.

If you suspect you might have a bad CV joint, bring your vehicle in so a technician can determine what’s going on.  Keep your CV joints in good shape and reduce the risk of them seizing up at an inopportune time so you can avoid being stranded.

Hill's Auto Repair, Inc.
22829 colton point rd
Bushwood, Maryland 20618
301-769-2400